Miniature Fret End Bevel Diamond File, 90&35 degrees 2 grits. Luthier Tool TF027 ORDER BY 2pm, SAME DAY DISPATCH BY ROYAL MAIL 1st CLASS

EUR 20,61 Achat immédiat 25d 4h, EUR 6,46 Livraison, 30-Day Retours, Remboursement si vous n'avez pas reçu ce que vous aviez commandé en cas de paiement avec PayPal.

Vendeur: Top-Rated Seller chrisalsopguitarbits (8.854) 100%, Lieu où se trouve: Woodville, Derbyshire, Lieu de livraison: Worldwide, Numéro de l'objet: 181405893089 Order by 2.00 pm for SAME DAY DISPATCH - UK get it next day ! Miniature Fret End Bevel File. 45mm Diamond File. 90 or 35 degrees. Designed and Made By Chris Alsop in his workshops in Derbyshire, UK. This is a minature sized bevel file with the file length 45mm. The diamond file passes through a slot in an angled block. Where the file exits the block a 90 degree or 35 degree angle is made. The file fits the slot securely and is held in place with an allen screw to prevent the file moving. By sliding the file into the block either the 90 of 35 degree angle is obtained and the amount the file protrudes from the block can also be altered. This tool is ideal for bevelling the odd fret or for doing a few frets following a partial refret. Our larger bevel files are recommended for bigger jobs. Ideally this short file , at only 45mm, is best used to produce the correct angle on a single fret. Reducing the length of the fret to roughly the correct length is best done using a longer ,coarser, file - and to use this little file to finish the angle correctly and get a nice smooth finish. You should always use a fretboard protector / fingerboard guard when working on frets These files are suitable on stainless frets and normal nickel silver frets. Dimensions • 35 degrees or 90 Angled Bevel File • 45mm File Length • Fine AND Coarse Grit Diamond Files included Features The tool provides an efficient and easy to use solution to getting the fret ends cleanly cut to a specific angle. The tool has the main features: • For beveling the fret end the file is set at 35 degrees or 90 degrees. • Changeable Files. Different grits can be installed. • Smooth base made of low friction polymer, with bevelled at the ends. This base makes it easy to pass over the fret tops without damage the frets. • Robust construction from highest grade engineering polymer and professional quality diamond file. • Suitable for Stainless Steel frets Fret Beveling in General The main advantage of using a Bevel File is that a really consistent professional job is achieved where all the fret ends are at the same angle. This main point about bevelling is to make sure there are no sharp edges or uncomfortable fret ends which hamper playing. If a fret end is too long then it disturbs the feel of the neck as the players moves around the fretboard; if the fret end angle is too shallow then the string can easily start to slip off the end of the fret. It is also surprising just how much of the fretboard space is used up by the bevels - a 45 degree bevel will use about 1mm of the fret wire and so reduce a 43mm neck to 41mm playable width. These bevel files can be made to any angle as low as zero and to a maximum of 60 degrees (please enquire). The cutting files are a diamond files. Using the fine diamoond file leaves a good finish and all that is needed is the final light sanding to remove any scratches or uncomfortable edges and finally a polish. FREE WITH THIS ITEM • Advice sheet on use of this tool • A comprehensive guide to fret replacement Other Products We produce a wide range of guitar tools. All tools are produced from our workshop in Woodville, Derbyshire, UK by Chris Alsop. See our eBay shop for Fret Pullers and Cutters, Fret Bevel Diamond Files, Fretboard Protectors, Crowning and Dressing Diamond Files, Guitar Neck Rests, Fret Levelling Diamond Files, Fretting hammers, Fret Polishing and Sanding Kits, String Action Gauges, Guitar Pin Pullers and String Winders. Also, see our eBay shop for a wide variety of Custom Made Guitar Saddles, Nuts and Pins - all made by Chris Alsop to customer specified dimensions. We offer these components in many materials, specialising in crafted high quality Buffalo Bone and European Hardwoods. Shipping • We offer shipping discount on postage on multiple item orders. • Postage is calculated as the highest shipping cost is full rate and then any additional items are ONLY 25% of shipping cost. • Fast Shipping. Order by 2pm for same day dispatch on most tools. • We ship all our items by Royal Mail using 1st Class (UK) and International Tracked (Overseas). • For UK orders, we also offer Royal Mail Guaranteed by Next Day service. Condition: New, Tool Type: Minature Fret End Bevel File, Country/Region of Manufacture: United Kingdom, Material: Diamond FIle & Black Polymer, Type: Luthier Tools, MPN: TF027, Brand: Chris Alsop Guitar

blogdelfreelance.com Insights blogdelfreelance.com Exclusif
  •  Popularité - 18.752 vues, 11.3 views per day, 1.655 days on eBay. Super grande quantité sur vues. 114 vendu, 447 disponibles.
  •  Prix -
  •  Vendeur - 8.854+ articles vendu. 0% évaluations négative. Vendeur Top Fiabilité! Expédié à temps avec suivi, 0 problèmes avec les ventes passées.
Articles similaires Items
Sitemap